Kinsler_Handbook_#32 April 2024

Kinsler Fuel Injection, Inc, 1834 THUNDERBIRD TROY, MICHIGAN 48084 U.S.A. www.Kinsler.com Phone (248) 362-1145 Fax (248) 362-1032 177 SHUT-OFF VALVES Pin removed, valve snaps closed Pin installed, valve is open SAFETY SERIES Ideal for boats and motorcycles, if driver is thrown from vehicle, cord attached to driver pulls pin, allowing spring loaded valve to snap shut. Billet aluminum mounting bracket is blue anodized and features a stainless steel pull pin. *** IMPORTANT*** DO NOT attach a cable or rod to valve arm when using it as a safety shut-off. STANDARD SERIES HFV SHUT-OFF VALVES Hard anodized aluminum housing with 8 AN male flare and 8 AN female ends, will flow in either direction. Overall length is 2.6” without adapter fittings. Ball type valve with spring loaded end seals and o-ring on actuation shaft. Arm rotates 360 o on standard series valve assembly and 90 o on safety series valve. Standard series valve has built-in detents every 90 degrees, this gives the valve a positive on/off position and it can be actuated by cable, linkage, or by hand. A large selection of adapter fittings makes this a very adaptable and flexible valve. Arm has a 3/16” clearance hole and 1.250” center to center for a 90 0 travel of 1.768”. Unit can be disassembled and new seals installed in the field. #6036 HFV shut-off valve with # 6043 8 AN adapter fitting installed 6036 Model 'HFV', neoprene seals, for gasoline and methanol ONLY 6038 Model 'HFV', teflon seals, for methanol and nitromethane 6037 Safety shut-off valve, same as #6036, with safety pull pin and mounting bracket, for gasoline and methanol ONLY 6039 Safety shut-off valve, same as #6038, with safety pull pin and mounting bracket, for methanol and nitromethane ADAPTER FITTINGS - COMMONLY USED ON HFV SHUT-OFF VALVE 6040 6 AN male flare x 8 AN female swivel, plated steel 6041 6 AN female swivel x 8 AN female swivel, aluminum 6042 8 AN female swivel x 8 AN male + o-ring, hard-anodized aluminum 6043 8 AN male flare x 8 AN male + o-ring, hard-anodized aluminum 6044 6 AN male flare x 8 AN male + o-ring, hard anodized aluminum 6047 8 AN male + o-ring x 8 AN male bulkhead + nut & o-ring, plated steel 6048 8 AN male + o-ring x 6 AN male bulkhead + nut & o-ring, plated steel © 2019 PARTS FOR HFV SHUT-OFF VALVES 6055 Seal kit for #6036 and #6037, for gasoline and methanol ONLY, includes two end seals, one shaft seal, and one arm roll pin 6056 Seal kit for #6038 and #6039, for methanol and nitromethane, includes two end seals, one shaft seal, and one arm roll pin 6051 Top plate assembly, for #6036 and #6038 valve, with arm and shaft 6052 Top plate assembly, for #6037 and #6039 valve, with arm and shaft 6053 Ball only, for #6036, #6037, #6038, #6039 shut-off valve 6059 O-ring, for shaft seal on #6036 to #6039 shut-off valve, specify fuel MOUNTING BRACKETS FOR HFV SHUT-OFF VALVES 6049 Bracket, for #6036 and #6038, panel mount, billet aluminum, two retaining screws for shut-off valve, two 10-32 mounting screws with washers, blue anodized 6050 Mounting plate, for use with #6049 bracket to mount 'HFV' shut-off valves on Kinsler 1-pc. big block Chevrolet injection manifold, billet aluminum, black anodized (polished finish optional) #6050 #6049 DIS CONTINUED DISCONTINUED DISCONTINUED