Kinsler 2026 Price List

Part No. Description List Resale DEALER 2026 PRICE SHEET KINSLER FUEL INJECTION 1/14/2026 KINSLER BILLET ALUMINUM FOUR BARREL THROTTLE BODIES: Standard Series, Holley 4150 bolt pattern. Overall height is 3". Features 5.125" diameter neck for air filter, with 1/4-20 threaded hole for air cleaner stud. Body machined for GM thread-in idle air control motor and 8AN female vacuum port. Motor or motor port plug sold separately. See below. 14105 750 CFM Holley 4150 bolt pattern, 1.525" bores 1642.10 1216.30 1219.55 14170 1000 CFM Holley 4150 bolt pattern, 1.700" bores *** NEW STYLE BILLET *** 1779.10 1317.80 1321.30 14175 1000 CFM Holley 4150 bolt pattern, 1.700" bores *** NEW STYLE BILLET *** with provision for Kinsler 1518.20 DRIVE-BY-WIRE motor High Flow Series, Holley 4500 bolt pattern. Overall height is 3.5". Features 7.312" diameter neck for air filter, with 1/4-20 threaded hole for air cleaner stud. Throttle body has 8AN female port at rear of base for vacuum reference or remote IAC plumbing. 14118 1325 CFM Dominator bolt pattern, 1.875" bores 2082.40 1542.50 1522.85 14118-IAC 1325 CFM Dominator bolt pattern, 1.875" bores, provision for bolt on high flow IAC motor 2291.30 1697.20 1675.65 14120 1600 CFM Dominator bolt pattern, 2.0" bores 2140.60 1585.60 1565.45 14120-IAC 1600 CFM Dominator bolt pattern, 2.0" bores, provision for bolt on high flow IAC motor 2349.50 1740.30 1718.10 HF V2 Series, Holley 4500 bolt pattern. Overall height is 2.55". Features 7.24" dia. neck for air filter pan, with 5/16-18 threaded steel insert hole for air cleaner stud. 1/2" dia. Counter rotating milled throttle shafts, 5 degree tapered throttle plates, ball bearing shaft supports with integral lip seal. Throtttle shaft end machined to accept tang style TPS. TPS purchased separately. (10697-BR or equivalent) 14122 1900 CFM V2 Dominator bolt pattern, 2.25" bores, with provision for Kinsler DRIVE-BY-WIRE motor. 2210.80 1637.60 1688.20 REPLACEMENT COMPONENTS FOR ABOVE #14122 V2 DominatorThrottle Body 4767 Bearing; special Kinsler, for 10mm shaft. 10mm ID, 19mm OD, 5mm wide (4 required) 11.65 4768 Clip; special Kinsler, ground for thickness to retain 10mm throttle shaft beating, external style (2 required) 2.05 14128 Dual Arm; 1.0" c-c with idle/WOT stop screws, 3/8" shaft, for Primary shaft on V2 4BBL 4150 & 4500 throttle 47.00 bodies, black anodized billet aluminum. 14129 Arm; 1.0" c-c for idle screw only, 3/8" shaft, for Secondary shaft on V2 4BBL 4150 & 4500 throttle bodies, 38.00 black anodized billet aluminum. 7717-L Throttle Return Spring; LH rotation, Super Light (1 required) 17.85 7717-R Throttle Return Spring; RH rotation, Super Light (1 required) 17.85 548-*** O-ring; #568-162, for 4500 throttle body base (inside o-ring) 1.95 568-*** O-ring; #568-163, for 4500 throttle body base (outside o-ring) 1.95 DBW COMPONENTS to fit above # 14122 Throttle Body DBW-V3 DBW ACTUATOR, Ver.3.0 with isolation housing mount model R3 and arm. 2636.75 43214 Billet Bracket to Mount DBW actuator to Billet Throttle body # 14222 & #14175 142.20 105.30 104.35 43178 Billet Dongle to connect DBW actuator to Billet Throttle body shaft, 4.515" C-C, for '4150' series #14175 4-bbl. 81.05 43184 Billet Dongle to connect DBW actuator to Billet Throttle body shaft, 5.228" C-C. 110.60 81.90 81.05 7108 Mounting Plate; for Novotechnik TPS, when used on Kinsler bearing manifold, 4-bolt pattern & internal o-ring. 72.60 14110 Upgrade; Progressive linkage, opens front throttles halfway before engaging rear throttles. 158.50 117.40 117.70 14112 Upgrade; Installation of bolt-on TPS boss with drive coupler. See TPS listing for selection. 123.80 91.70 92.10 14114 Throttle Return springs, inner and outer spring with stationary mount tab. 26.60 19.70 19.90 14088 Phenolic spacer; Holley 4150 bolt pattern, open style, .540" thick 64.00 47.40 47.55 14092 Phenolic spacer; Holley 4150 bolt pattern, open style, 2.055" thick 208.50 154.40 154.95 14093 Phenolic spacer; Holley 4500 bolt pattern, open style, .540" thick 66.60 49.30 49.55 14098 Phenolic spacer; Holley 4500 bolt pattern, Cloverleaf 4 hole open center, .540" thick 66.60 49.30 49.55 14081 Gasket; Holley 4150 standard, open style 11.30 8.30 8.35 14082 Gasket; Holley 4500 Dominator, open style 11.30 8.30 8.35 14083 Gasket; Holley 4500 Dominator, 4-hole style 11.30 8.30 8.35 14157 I.A.C. port plug; flange style, for high-flow style IAC, black-ano., used on new #14170 throttle body 73.10 54.10 54.40 6199 Plug; 20mm x 1.50, Idle Speed Motor Port, T-Body, blue anodize aluminum 75.80 56.10 56.30 10660 Idle Air Control Motor; General Motors, 20mm x 1.5 thread 116.60 86.30 86.60 10669 Idle Air Control Motor; General Motors style, bolt on design , 4 pin Metri-pack housing 115.90 85.80 86.20 10662 Housing; high flow, remote idle air control motor, 3/8" NPT inlet 141.80 105.00 105.40 10663 Air Filter; for #10662 high flow housing, K&N 52.60 38.90 40.55 10668 Pre-Filter; Outerwears, fits over # 10663 K&N air filter 14.50 10.70 10.95 10664 Housing; turbocharged, remote idle air control motor, two 8AN female inlet ports 217.30 160.90 161.45 3535 Mounting Bracket; adapt KFI barrel valve to KFI 4150 throttle body 174.90 129.50 130.05 Base has o-ring for sealing to intake. Throttle bore exit size is 4.775" square. Page 65 of 82