Kinsler_Handbook_#32 December 2017

Kinsler Fuel Injection, Inc, 1834 THUNDERBIRD TROY, MICHIGAN 48084 U.S.A. www.Kinsler.com Phone (248) 362-1145 Fax (248) 362-1032 171 SHUT-OFF VALVES © 2017 Service Kits Consists of : piston, spring, plunger, retainers, and seal. 6068-B Buna nitrile seal, for #6060 and #6062 SS-12 normally closed 6068-T Teflon seal, for #6060 and #6062 SS-12 normally closed 6069-B Buna seal, for #6061 / #6063 SS-12 normally open Model: SS-12 Buna seals, stainless steel body. Weighs approx. 1.9 lbs and includes male/female Weather-Pack two pin sealed connector assembly. Seat orifice is 3/8” I.D. Two 10-32 threaded mounting holes located in base. Has 1/4”NPT female inlet and outlet port. Maximum operating pressure: 150 PSI. Maximum fluid temperature: 230 0 F. Model: SS-13 (Not Shown) Teflon seals, stainless steel body. Weighs approx. 1.3 lbs and includes male/female Weather-Pack two pin sealed connector assembly. Seat orifice is 1/4” I.D. Two 10-32 threaded mounting holes located in base. Has 1/4”NPT female inlet and outlet port. Maximum operating pressure: 100 PSI. Maximum fluid temperature: 180 0 F. Buna seals, brass body. Weighs approx. 1.3 lbs and includes male/ female Weather-Pack two pin sealed con- nector assembly. Seat orifice is 11/64” I.D. Has 1/4”NPT female ports. Maximum operating pressure: 11 PSI. Maximum fluid temperature: 180 0 F. Recommend: For gasoline and methanol - buna seals For methanol / nitro - teflon seals Note: teflon seals may not produce a dripless seal. #6060 with two #6160 6 AN male flare adapter fittings Phil Sonner’s 55’ Chevy with a Kinsler EFI system on a 454 big block SOLENOID SHUT-OFF VALVE, 12-VOLT DC Consult us for proper use and application of this unit. A) Can be utilized for shut-off of complete gasoline system. B) Manual Lean-Out or enrichment system, can be activated by driver. C) Can be wired for vehicles with automatic transmission and a transbrake or with a MSD two-step RPM control. D) Excellent for fuel system which requires two different main jet selections, good launch and good mid-range. 6060 Valve assembly, normally closed (opens when power is applied), buna seals, model: SS-12 6061 Valve assembly, normally open (closes when power is applied), buna seals, model: SS-12 6062 Valve assembly #6060, normally closed (opens when power is applied), with restrictor jet holder installed in outlet and 6 AN male flare inlet fitting 6063 Valve assembly #6061, normally open (closes when power is applied), with restrictor jet holder installed in outlet and 6 AN male flare inlet fitting 6064 Valve assembly, normally closed (opens when power is applied), model: SS-13. Teflon seals, stainless steel body, includes 6 AN male flare fittings 6064-R Valve assembly, normally closed (opens when power is applied), model: SS-13. Teflon seals, stainless steel body, includes 6 AN male flare fittings inlet and restrictor jet holder installed in outlet 6067 3-way flow divertor valve, 12-volt DC, 1/4" NPT female ports, 11 PSI max., 180 F max. fluid temperature o

RkJQdWJsaXNoZXIy ODE2MjA=