Kinsler 2026 Price List

Part No. Description List Resale DEALER 2026 PRICE SHEET KINSLER FUEL INJECTION 1/14/2026 8AN HILBORN HIGH FLOW JET CAN 3055 Hilborn Jet Can; 8AN, hard anodized aluminum, includes spring & poppet 199.80 148.00 148.55 3054 Body Only; 8AN, hard anodized aluminum 144.20 106.80 107.20 3057 Poppet; hard anodized aluminum, for #3055 jet can 52.30 38.70 38.90 8AN BRASS HIGH FLOW JET CAN 3061 Brass Jet Can; 8AN, with precision ground steel poppet & spring 190.30 140.90 141.25 3063 End Cap Only ; BRASS, for 8AN #3061 high flow jet can only, with jet sealing o-ring 43.20 32.00 32.30 3062 Poppet; for #3061, #3050 & #3082 8AN jet can 70.80 52.40 52.75 3082 Brass Jet Can; 8AN, for pressures in excess of 200 psi, uses extra long spring 205.00 151.80 152.35 3053 End Cap Only ; Aluminum, for 8AN #3082 high pressure 8AN jet can valve 60.70 44.90 45.10 8AN ALUMINUM HIGH FLOW JET CAN 3050 Aluminum Jet Can; 8AN, with precision ground steel poppet & spring 223.10 165.20 165.70 3051 End Cap Only ; ALUMINUM, for 8AN high flow jet can, w/jet sealing o-ring 50.00 37.00 37.20 3062 Poppet; for #3061 & #3050 8AN jet can 70.80 52.40 52.75 SPRINGS: For 8AN Jet Can Valves 3064 Spring; for 8AN brass jet can, state size in wire diameter x length: $ each 13.30 9.80 10.00 .027" x 1.530", .035" x 1.530", .034" x 1.870", .047" x 1.500", .060" x 1.430" .058" x 1.450", .074" x 1.510", .076" x 2.050" Specify Size 3130 Spring Kit; "LIGHT", approx. 3-40 PSI range, fits 3061 and 3050 valve assemblies. 45.80 33.90 34.05 3131 Spring Kit; "HEAVY", approx. 38-300 PSI range, fits 3061 and 3050 valve assemblies. 45.80 33.90 34.05 3078 Spring Kit; consists of the above eight springs for 8AN jet can. 82.50 61.10 61.35 3058 Spring; for Hilborn 8AN jet can #3055, state size in wire dia: .024" or .047" $ each 12.90 9.50 9.65 SHIMS: For 8AN Jet Can Valves 3059 Shim Kit; four .020", two .060", one .185" shims per kit 18.80 13.90 14.00 3065 Shim; thin, .020" thick, brass, for 8AN jet can 2.90 2.10 2.30 3066 Shim; medium, .060" thick, brass, for 8AN jet can 3.40 2.50 2.65 3067 Shim; thick, .185" thick, brass, for 8AN jet can 4.60 3.40 3.50 JET SELECTOR VALVE 3404 Jet Selector Valve-XL; extra lightweight, for gas & methanol, hard anodized 625.10 463.00 464.30 3455 Rotor; service replacement item only, not sold outright 204.60 151.50 151.95 3460 Knob; complete w/detent pins, springs, set screws & indicator pin, for JSV #3403 98.20 72.70 73.10 3461 Knob; complete w/detent pins, springs, set screws & indicator pin, for XL-JSV #3404 106.40 78.80 79.10 3465 Shaft; service replacement item only, not sold outright, for JSV #3403 64.00 47.40 47.55 3466 Shaft; service replacement item only, not sold outright, for XL-JSV #3404 64.00 47.40 47.55 3410 Spring; jet retaining, $ each 4.90 3.60 3.75 3411 Spring; for knob detent, two required, $ each 8.10 6.00 6.10 3412 Detent Pin; for knob, two required, $ each 24.20 17.90 18.00 3413 O-ring; to seal main body to cap, large diameter 5.70 4.20 4.25 3414 O-ring; to seal rotor shaft to main body, gasoline/methanol 3.20 2.30 2.40 3430 Trim Plate; for Jet Selector Valve #3403, includes mounting screws 46.90 34.70 34.90 3440 Installation Kit; for Jet Selector, includes trim plate, springs, shim, 76.50 56.60 56.90 instructions, lapping paper, 3 spare body o-rings & mounting screws RANGE JET VALVE 3020 Range Jet Valve; for use with Jet Selector on jetting above .100" 235.20 174.20 174.75 Complete with swivel-T fittings, jets NOT included JETS: K-Type, Flowed & Matched 3710 Labor; to SPECIAL make ONE K-type jet, .014" to .028" at .002" 84.70 62.70 62.95 3711 Labor; to SPECIAL make ONE K-type jet, .030" to .038" at .002" 63.90 47.30 47.50 3712 Labor; to SPECIAL make ONE K-type jet, .040" to .048" at .002" 41.10 30.40 30.60 3713 Labor; to make ONE standard size K-type jet, .050" to .186" at .002" 28.90 21.40 21.50 3714 Labor; to make K-type matched jet SET, 8 to 12 jets per SET, 229.10 169.70 170.25 state sizes: .050" to .186" at .002" increments 3715 K-type jet blank; to make above matched jets, $ each 7.30 5.40 5.50 JETS: Enderle & Hilborn 3073 Enderle Jet; screw-in type, unmatched, state sizes: 10.20 7.50 7.70 .020" to .200" at .005" increments, $ each 3054 Hilborn 6AN Jet; for Hilborn & Kinsler jet can valves, unmatched, 10.65 state sizes: .020" to .250" at .005" increments, $ each 3060 Hilborn 8AN Jet; unmatched, for #3055 jet can valve, specify size 21.90 16.20 16.35 Page 2 of 82