Kinsler_Handbook_#32 December 2017

191 1834 THUNDERBIRD TROY, MICHIGAN 48084 U.S.A. www.Kinsler.com Phone (248) 362-1145 Fax (248) 362-1032 Kinsler Fuel Injection, Inc, AIR FILTRATION When building an air box filter, the top plate should be mounted a minimum of .7 x ramtube inside di- amter above the top of the ramtubes. Example: .7 x 2.5” diameter = 1.75”. The base plate should be sealed to the ramtubes. Leave enough room below it to adjust the barrel valve and throttle stops. Maintain a minimum of 1 1/2” from the straight part of the ramtubes to the sides of the filter ele- ment. For dirt track racing we recommend that you construct a sheet metal shield that mounts about 1 1/2” from the outside of the element, like an upside-down box. This will deflect dirt thrown by the tires. In cases where it is not practical to use filter-element-sides for your air box, you can construct the air box using sheet metal sides and duct filtered air from a remote filter via large diameter flexible tubing. Oiling the foam will increase it’s effectiveness in trapping fine dirt. Use K&N oil (Kinsler #5043) or about 1 tablespoon of 10W oil per square foot of foam. Put the oil on the foam and then wring the element until the oil is evenly distributed. DO NOT OVER OIL !!! To clean the filter foam, use a non-flamable water based cleaning solution that cuts oil: water with dish soap, Kinsler #5042 K&N air filter cleaner, etc. Thoroughly dry the foam before reinstalling, then re-oil it. CARBURETORS Our filter foam is excellent for use with carbs. It can be used to construct a replacement for your original element, or you can use it to build a custom air filter system. CLEANER AND OIL FOR K&N ® AIR FILTERS 5042 Cleaner, 32 fluid ounce spray bottle 5043 Oil, 12 fluid ounce aerosol can OUTERWEARS ® PRE-FILTERS FOR K&N AIR FILTERS Helps keep dirt and mud from being packed into the pleats of your K&N filters, to save time and effort in cleaning. Pre-Filters can be washed and reused. Available for all Kinsler small block Chev, Mo- par, Ford, Buick injection units. Custom made units are available. 5190 Fits Kinsler with K&N siamese air filter, each 5191 Fits Kinsler with K&N single air filter #5120 and #5121, each 5192 Fits Hilborn with K&N siamese air filter, each 5193 Fits Hilborn with K&N single air filter, each 5194 Fits aluminum air box panel filter #5122 5195 Fits carbon fiber air box #5151 for 8 cylinder 5196 Fits carbon fiber air box #5152 for 4 cylinder 5197 Fits #5123 K&N air filter for valve cover breather 5198 Fits #10663 K&N idle air control housing air filter, for Kinsler remote mount I.A.C. © 2017 o 5100 Hilborn 2 1/16" single ramtube, no angle, set of 8 5101 Hilborn 2 1/16" single ramtube, 5 , set of 8 5102 Hilborn 2 1/16" small block Chevrolet V8, siamese, set of 4 5103 Hilborn 2 3/16" single ramtube, no angle, set of 8 5104 Hilborn 2 3/16", single ramtube, 5 , set of 8 5105 Hilborn 2 3/16" small block Chevrolet V8, siamese, set of 4 5106 Hilborn 2 7/16", single ramtube, no angle, set of 8 5107 Hilborn 2 7/16", single ramtube, 5 , set of 8 5108 Hilborn 2 7/16" small block Chevrolet V8, siamese, set of 4 5109 Hilborn 2 7/8" big block Chevrolet V8, siamese, set of 4 5111 Kinsler and Crower 2.9" big block Chevrolet V8, 5 , requires removal of ramtube bell, set of 8 5112 Kinsler 2 3/16" and 2 1/4" small block Chev. V8, siamese, set of 4 5113 Kinsler 2 3/8" and 2 7/16" small block Chev. V8, siamese, set of 4 5114 Kinsler 2 1/2", 2 5/8", 2 11/16” small block Chev. V8, siamese, set of 4 5115 Kinsler and Engler 2 11/16", small block Chev. V8, siamese, set of 4 5119 Kinsler Pontiac 4-cylinder Super-Duty, 2 1/4" and 2 1/2" 5120 Kinsler small block Ford V8, all sizes (may require turning O.D. of ramtube bell), set of 8 5121 Kinsler small block Chevrolet with Dart/Buick cylinder heads, all sizes (may require turning O.D. of ramtube bell), set of 8 5123 Valve cover breather, 1"I.D. neck, 3"O.D., 2 3/8" tall 5124 Oval element, inside 22.75" long x 4.25" wide x 2.43" tall 5125 Kinsler PSI T-body air box, triangle shape, 6 1/2" tall 5126 Oval element, inside 7.37" long x 3.75" wide x 2" tall 5127 Lid, for siamese ramtube K&N filter, aluminum 5128 Clamp, for base of siamese ramtube K&N filter, stainless steel o o o - CONTINUED - K & N ® AIR FILTERS If you don’t see the filter you need, call us. Other filter sizes and custom filters are available.

RkJQdWJsaXNoZXIy ODE2MjA=